NightWhen the car breaks down while driving and you need to stop, try to choose a safe area to park, turn on the hazard alarm flash, outline light and rear light, and set a warning sign at the rear of the car.
When a motor vehicle breaks down on the road and needs to be stopped to troubleshoot, the driver should immediately turn on the hazard alarm flash, and then move the vehicle to a place that does not interfere with traffic before troubleshooting.
Increase the distance from the car. When the driver is driving at night. First, the view is not as wide as it is during the day. Second, there are frequent dangers and emergencies. For this reason, the driver must be ready to stop at any time. In this case, in order to avoid danger, attention should be paid to appropriately increasing the distance from the car to prevent front and rear car collisions.
When a motor vehicle breaks down on the road and needs to be stopped to eliminate, the driver shouldShould: Turn on the danger alarm light, park the motor vehicle in a place that does not obstruct traffic, and put a signal warning sign 50~100m behind the car. If it is on a regular road, if the car is already difficult to move, the danger alarm light should be turned on continuously.
The correct thing to do when a motor vehicle stops on the highway due to a fault is to set up a fault warning sign 150 meters behind the car, turn on the outline light and rear light at night, and turn on the danger alarm flash.
When a motor vehicle is driving at night without street lights, poor lighting, etc., it should be turned on Headlights, contour lights, rear lights and brake lights.Headlights are the main lighting equipment for motor vehicles to drive at night. They can provide forward lighting so that drivers can clearly see the roads and obstacles ahead and ensure driving safety.
When driving without poor street lights, the headlights, contour lights and rear lights should be turned on.
When there are no street lights at night, the high beams should be turned on when driving under poor lighting conditions. Car high beams are generally suitable for motor vehicles at night on roads without street lights or poorly lit, such as driving on dimly lit national highways or highways. Due to the good lighting in the urban area, lo-beam lights must be used.
When driving under bad conditions without street lights at night, the driver should turn on appropriate lights to ensure driving safety. Depending on the situation, you can choose to use high beams, lom beams, fog lights, etc.First of all, when driving on a road without street lights at night, the driver should turn on the lom beam.
The headlights, contour lights and rear lights should be turned on when driving at night without poor street lights. At the same time, the fog lights and danger alarm flash should be turned on when driving in the fog. If you are driving on a road without street lights or poorly lit at night, you should turn on the high beam.
When the vehicle is driving at night, if the lighting environment is bad, you need to turn on your own headlights, which is the lighting equipment with the highest brightness on the car. This headlight can avoid vehicle accidents caused by unclear realization at night. The specific operation steps for turning on are as follows: open the door on this side of the cab. Step on the brake pedal.
1. When the driver drives at night, firstly, his vision is not as wide as it is during the day, and secondly, it often encounters danger and emergencies. For this reason, the driver must be ready to stop at any time. In this case, in order to avoid danger, attention should be paid to appropriately increasing the distance from the car to prevent front and rear car collisions.
2. When driving at night, if there are opposite cars, do not step on the pedal for a while, turn right for a while, and pay close attention to pedestrians and bicycles on the right.
3. Therefore, when we drive at night, we should increase the distance from the car and be vigilant to deal with various situations that may occur at any time.
1. Use low beams when the lighting conditions of urban roads at night are good. Turn on the high beam on roads with poor lighting conditions at night, but you should change the light beams in time when meeting.
2. Try to use high beams in places with poor lighting at night. When there is a car on the opposite side, switch the light to the low beam in time, so as not to dazzle the driver on the opposite side.
3. Pay attention to controlling the speed: At night, people's eyes cannot adapt to external light for the time being. Drivers should slow down as much as possible and pay close attention to pedestrians and vehicles on the road. At night, there are fewer and fewer pedestrians and vehicles on the road. The driver has adapted to the external light, and the visibility will be better and better. Pay attention to the use of lights: Don't turn on the lights randomly during driving.
4, 9 The use of lights when passing through curves. When passing through the curve, the distance of the light gradually becomes farther. You should change the high and lom lights in advance, and proceed according to the normal night driving operation.
Trade Data intelligence-APP, download it now, new users will receive a novice gift pack.
NightWhen the car breaks down while driving and you need to stop, try to choose a safe area to park, turn on the hazard alarm flash, outline light and rear light, and set a warning sign at the rear of the car.
When a motor vehicle breaks down on the road and needs to be stopped to troubleshoot, the driver should immediately turn on the hazard alarm flash, and then move the vehicle to a place that does not interfere with traffic before troubleshooting.
Increase the distance from the car. When the driver is driving at night. First, the view is not as wide as it is during the day. Second, there are frequent dangers and emergencies. For this reason, the driver must be ready to stop at any time. In this case, in order to avoid danger, attention should be paid to appropriately increasing the distance from the car to prevent front and rear car collisions.
When a motor vehicle breaks down on the road and needs to be stopped to eliminate, the driver shouldShould: Turn on the danger alarm light, park the motor vehicle in a place that does not obstruct traffic, and put a signal warning sign 50~100m behind the car. If it is on a regular road, if the car is already difficult to move, the danger alarm light should be turned on continuously.
The correct thing to do when a motor vehicle stops on the highway due to a fault is to set up a fault warning sign 150 meters behind the car, turn on the outline light and rear light at night, and turn on the danger alarm flash.
When a motor vehicle is driving at night without street lights, poor lighting, etc., it should be turned on Headlights, contour lights, rear lights and brake lights.Headlights are the main lighting equipment for motor vehicles to drive at night. They can provide forward lighting so that drivers can clearly see the roads and obstacles ahead and ensure driving safety.
When driving without poor street lights, the headlights, contour lights and rear lights should be turned on.
When there are no street lights at night, the high beams should be turned on when driving under poor lighting conditions. Car high beams are generally suitable for motor vehicles at night on roads without street lights or poorly lit, such as driving on dimly lit national highways or highways. Due to the good lighting in the urban area, lo-beam lights must be used.
When driving under bad conditions without street lights at night, the driver should turn on appropriate lights to ensure driving safety. Depending on the situation, you can choose to use high beams, lom beams, fog lights, etc.First of all, when driving on a road without street lights at night, the driver should turn on the lom beam.
The headlights, contour lights and rear lights should be turned on when driving at night without poor street lights. At the same time, the fog lights and danger alarm flash should be turned on when driving in the fog. If you are driving on a road without street lights or poorly lit at night, you should turn on the high beam.
When the vehicle is driving at night, if the lighting environment is bad, you need to turn on your own headlights, which is the lighting equipment with the highest brightness on the car. This headlight can avoid vehicle accidents caused by unclear realization at night. The specific operation steps for turning on are as follows: open the door on this side of the cab. Step on the brake pedal.
1. When the driver drives at night, firstly, his vision is not as wide as it is during the day, and secondly, it often encounters danger and emergencies. For this reason, the driver must be ready to stop at any time. In this case, in order to avoid danger, attention should be paid to appropriately increasing the distance from the car to prevent front and rear car collisions.
2. When driving at night, if there are opposite cars, do not step on the pedal for a while, turn right for a while, and pay close attention to pedestrians and bicycles on the right.
3. Therefore, when we drive at night, we should increase the distance from the car and be vigilant to deal with various situations that may occur at any time.
1. Use low beams when the lighting conditions of urban roads at night are good. Turn on the high beam on roads with poor lighting conditions at night, but you should change the light beams in time when meeting.
2. Try to use high beams in places with poor lighting at night. When there is a car on the opposite side, switch the light to the low beam in time, so as not to dazzle the driver on the opposite side.
3. Pay attention to controlling the speed: At night, people's eyes cannot adapt to external light for the time being. Drivers should slow down as much as possible and pay close attention to pedestrians and vehicles on the road. At night, there are fewer and fewer pedestrians and vehicles on the road. The driver has adapted to the external light, and the visibility will be better and better. Pay attention to the use of lights: Don't turn on the lights randomly during driving.
4, 9 The use of lights when passing through curves. When passing through the curve, the distance of the light gradually becomes farther. You should change the high and lom lights in advance, and proceed according to the normal night driving operation.
Global HS code repository access
author: 2024-12-23 10:42Solar panel imports HS code references
author: 2024-12-23 10:41HS code mapping in government tenders
author: 2024-12-23 10:39Trade data solutions for freight forwarders
author: 2024-12-23 09:59China HS code interpretation guide
author: 2024-12-23 10:36API integration with HS code databases
author: 2024-12-23 10:10How to map complex products to HS codes
author: 2024-12-23 08:39Import data trends visualization
author: 2024-12-23 08:39HS code-based opportunity scanning
author: 2024-12-23 08:34788.51MB
Check554.74MB
Check596.87MB
Check379.27MB
Check812.55MB
Check998.34MB
Check835.24MB
Check183.92MB
Check821.95MB
Check863.88MB
Check244.39MB
Check513.26MB
Check573.22MB
Check812.15MB
Check766.75MB
Check251.64MB
Check611.89MB
Check566.12MB
Check698.42MB
Check874.37MB
Check841.97MB
Check486.96MB
Check162.62MB
Check437.99MB
Check953.62MB
Check553.42MB
Check437.89MB
Check781.44MB
Check428.82MB
Check141.44MB
Check921.68MB
Check997.36MB
Check461.19MB
Check394.37MB
Check311.92MB
Check772.73MB
CheckScan to install
Trade Data intelligence to discover more
Netizen comments More
329 How to select the best trade data provider
2024-12-23 10:43 recommend
1216 Aggregated global trade insights dashboard
2024-12-23 10:18 recommend
1084 Mining industry HS code analysis
2024-12-23 09:32 recommend
962 Electronics global trade by HS code
2024-12-23 09:07 recommend
2527 Supply chain data
2024-12-23 08:55 recommend