1. The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seatAnd the disassembly of the rear backrest, the rear seat is only locked, but the rear backrest needs to be disassembled by unscrewing the folding screw. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
2. Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
3. [Pacific Automobile Network] The front seat needs to remove the screws of the base. There are four fixing screws in total. First, push the seat to the front, remove the front two screws, and then push the seat to the front and remove the back two screws. The seat was removed. Car seats are basically divided into leather seats and velvet seats.
4. You can put your hand in and touch it at the junction of the base and the backrest. There is a place stuck inside.Press it in a little, lift it up and take it apart. On the other hand, you can disassemble the seat cushion in the same way.
5. Find both sides of the head of the rear seat, pull the wrench, and install it in reverse order of disassembly and installation. Find the wrench on both sides of the head of the rear seat, close to the window, and pull the wrench. The backrest of the rear seat can be turned forward. Lift the rear seat up to remove the cushion, and install it in reverse order of disassembly and installation.
The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seat and the disassembly of the rear backrest. The rear seat is only locked, but the rear seat needs to be unscrewed off the fixing screw of the folding page for disassembly. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
Disassembly method: On both sides of the head of the rear seat, near the window, there will be a handle, pull the handle, and the backrest of the rear seat can be turned forward., most of the cushion part of the rear seat is squeezed directly to the rear of the car, and then lifted up to come out.
First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover. Then find the chuck and hook in the gap (between the backrest and the cushion) and take them out of the gap.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
First, press the button under the rear seat of SAIC General Motors Chevrolet, as shown in the figure below.At this time, you can find the fixing screw on the rear seat of the SAIC GM Chevrolet vehicle, and then remove the fixing screw on the rear seat. Next, you can remove the rear seat cushion of SAIC GM Chevrolet vehicles, see the figure below for details.
The method of disassembly of the car seat cover is as follows: pull open the rubber band behind the backrest headrest and untie the pasted Velcro. Take out the snap that fixes the seat cover from the bottom of the seat, and you can remove the entire seat cover from the bottom to the top.
The disassembly process of the car seat cover is as follows: 1. There will be a sticky buckle on the headrest cover, which can be removed by tearing off the adhesive buckle. Most of the seat covers of the main and co-drivers are fixed with zippers or fasteners, and the fasteners can be removed.
Removing steps for the rear seat cushion of the car (left/middle/right position common): First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover.
Installation and disassembly of the rear seat cushion of the car Remove the headrest of the rear seat, cover the seat backrest on the backrest, fix the top of the seat cover with a hook, and the bottom is stuffed into the gap between the backrest and the cushion through the cushion chuck. Cover the cushion on the rear cushion and fix it again through the cushion cuck into the gap of the backrest such as the cushion.
Car seat leather removal process. There will be a sticky buckle on the head pillowcase. Tear open the adhesive buckle and you can take it off. Most of the seat covers of the main and secondary driving are fixed by zippers or adhesive buckles, which can be taken off by tearing off the adhesive buckles.
The steps for removing the car seat cover are as follows: there will be an adhesive buckle on the headrest cover, and you can tear off the adhesive buckle and take it off. The seat covers of the main and co-drivers are mostly fixed with zippers or adhesive buckles, and they can be taken off by tearing the adhesive buckles.
1. Disassembly method: x0dx0a On both sides of the head of the rear seat, close to the window, there will be a handle, pull the handle, the backrest of the rear seat can be turned forward, the back Most of the cushions of the seats are squeezed directly to the back of the car, and then lifted up to come out.
2. The first thing that needs to be disassembled is the seat cushion, which is usually connected to the base. Use a tool to remove the screw fixing the seat cushion and remove it.Then gently remove the fixing point of the seat cushion and the base with your hand to make it detached.
3. The steps for removing the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat, close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion. Just install it in the reverse order of disassembly and installation.
4. The first step is to find the screws connected and fixed to the rear seat of the car. These screws are in the bottom area of the rear seat of the car and can be removed with a No. 5 wrench or wrench sleeve. Then gently lift the rear seat of the car to remove the barbed wire under the chair. The second step is to remove the headrest of the rear seat of the car.
1. The seat disassembly method of Volkswagen Touareg is as follows: Front seat: There are screws at the end of the slide and slide hard to the end. Rear seat: There is a fixing bolt at the bottom of the seat. If you lift the cover, you can see that the seat can be disassembled by unscrewing the screws and lifting them up hard.
2. Front row: there are screws at the end of the slide, screw it down, slide hard to the end and come down; back row: there are two screws in the calf, screw it down and lift it up hard. As shown in the figure, there is a fixing bolt at the bottom of the seat. You can see the fixing screw when you lift the cover cloth. If you unscrew the screw, you can loosen the seat.
3. The disassembly method of Volkswagen Touareg seats, the seats are fixed with screws. To remove them, the owner needs to remove the screws. The front seat screw is located in front of the track. After removing it, the seat is pushed out. The rear seat screw is located in its calf position. Remove it and then lift the chair hard.
4. There is a pull strap in the middle of the rear seat. Pull the inside of the pull strap up, and the rear seat can be removed. After that, you can take off the rear seat. Take off the left hook on the rear seat.
5. The method of removing the rear seat of Volkswagen Touareg and Wu Baiwan is as follows: Open the trunk, find the lock under the seat, and press the lock. Lift the front of the seat to separate it from the bottom of the seat. Find the foot under the front end of the seat and rotate it in the direction of the arrow on the foot to separate it from the bottom of the seat.
The steps to disassemble the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat and close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion.Just install it in the reverse order of disassembly and installation.
First of all, you need to find the fixing bolts under the seat. These bolts are usually located on both sides of the bottom of the seat, and there may be one or more. Use a wrench or wrench kit to remove these bolts. If the bolts are tight, you can use lubricant or a slight force to loosen them. Next, the seat needs to be put down.
Disassemble the rear seat of Arizer 8 as follows: First, the owner needs to find the latches of the four safety seats on the rear seat of the car, and then gently pick off the lid on the latch.
The rear seat of the vehicle is not tight after being disassembled once, because the buckle of the seat is broken. If the buckle is broken, it needs to be replaced in the repair shop. The replacement price is about 100 yuan. Generally speaking, there will be three seats in the rear seat, and there are four snaps in total. When a snap is broken, the seat will not be too tight.
Disassembly method of the rear seat of the car: on both sides of the head of the rear seat, close to the window, there will be a handle, pull handle, the backrest of the rear seat can be turned forward, and most of the cushion position of the rear seat is directly squeezed to the rear of the car and lift it up.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
Industry-specific HS code database-APP, download it now, new users will receive a novice gift pack.
1. The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seatAnd the disassembly of the rear backrest, the rear seat is only locked, but the rear backrest needs to be disassembled by unscrewing the folding screw. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
2. Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
3. [Pacific Automobile Network] The front seat needs to remove the screws of the base. There are four fixing screws in total. First, push the seat to the front, remove the front two screws, and then push the seat to the front and remove the back two screws. The seat was removed. Car seats are basically divided into leather seats and velvet seats.
4. You can put your hand in and touch it at the junction of the base and the backrest. There is a place stuck inside.Press it in a little, lift it up and take it apart. On the other hand, you can disassemble the seat cushion in the same way.
5. Find both sides of the head of the rear seat, pull the wrench, and install it in reverse order of disassembly and installation. Find the wrench on both sides of the head of the rear seat, close to the window, and pull the wrench. The backrest of the rear seat can be turned forward. Lift the rear seat up to remove the cushion, and install it in reverse order of disassembly and installation.
The disassembly method of the rear seat of the car is as follows: the disassembly of the rear seat of the car is divided into the disassembly of the rear seat and the disassembly of the rear backrest. The rear seat is only locked, but the rear seat needs to be unscrewed off the fixing screw of the folding page for disassembly. First, open the rear door of the car. Pull up the lock position of the rear seat to remove the rear seat.
Generally, the seat cover does not need to be removed from the backrest. After putting the seat down, take out the headrest and install it.
Disassembly method: On both sides of the head of the rear seat, near the window, there will be a handle, pull the handle, and the backrest of the rear seat can be turned forward., most of the cushion part of the rear seat is squeezed directly to the rear of the car, and then lifted up to come out.
First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover. Then find the chuck and hook in the gap (between the backrest and the cushion) and take them out of the gap.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
First, press the button under the rear seat of SAIC General Motors Chevrolet, as shown in the figure below.At this time, you can find the fixing screw on the rear seat of the SAIC GM Chevrolet vehicle, and then remove the fixing screw on the rear seat. Next, you can remove the rear seat cushion of SAIC GM Chevrolet vehicles, see the figure below for details.
The method of disassembly of the car seat cover is as follows: pull open the rubber band behind the backrest headrest and untie the pasted Velcro. Take out the snap that fixes the seat cover from the bottom of the seat, and you can remove the entire seat cover from the bottom to the top.
The disassembly process of the car seat cover is as follows: 1. There will be a sticky buckle on the headrest cover, which can be removed by tearing off the adhesive buckle. Most of the seat covers of the main and co-drivers are fixed with zippers or fasteners, and the fasteners can be removed.
Removing steps for the rear seat cushion of the car (left/middle/right position common): First of all, in order to have more operating space, the position of the front seat should be moved forward. Then you can open the snap of the fixed seat headrest cover, and take out both the headrest and the headrest cover.
Installation and disassembly of the rear seat cushion of the car Remove the headrest of the rear seat, cover the seat backrest on the backrest, fix the top of the seat cover with a hook, and the bottom is stuffed into the gap between the backrest and the cushion through the cushion chuck. Cover the cushion on the rear cushion and fix it again through the cushion cuck into the gap of the backrest such as the cushion.
Car seat leather removal process. There will be a sticky buckle on the head pillowcase. Tear open the adhesive buckle and you can take it off. Most of the seat covers of the main and secondary driving are fixed by zippers or adhesive buckles, which can be taken off by tearing off the adhesive buckles.
The steps for removing the car seat cover are as follows: there will be an adhesive buckle on the headrest cover, and you can tear off the adhesive buckle and take it off. The seat covers of the main and co-drivers are mostly fixed with zippers or adhesive buckles, and they can be taken off by tearing the adhesive buckles.
1. Disassembly method: x0dx0a On both sides of the head of the rear seat, close to the window, there will be a handle, pull the handle, the backrest of the rear seat can be turned forward, the back Most of the cushions of the seats are squeezed directly to the back of the car, and then lifted up to come out.
2. The first thing that needs to be disassembled is the seat cushion, which is usually connected to the base. Use a tool to remove the screw fixing the seat cushion and remove it.Then gently remove the fixing point of the seat cushion and the base with your hand to make it detached.
3. The steps for removing the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat, close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion. Just install it in the reverse order of disassembly and installation.
4. The first step is to find the screws connected and fixed to the rear seat of the car. These screws are in the bottom area of the rear seat of the car and can be removed with a No. 5 wrench or wrench sleeve. Then gently lift the rear seat of the car to remove the barbed wire under the chair. The second step is to remove the headrest of the rear seat of the car.
1. The seat disassembly method of Volkswagen Touareg is as follows: Front seat: There are screws at the end of the slide and slide hard to the end. Rear seat: There is a fixing bolt at the bottom of the seat. If you lift the cover, you can see that the seat can be disassembled by unscrewing the screws and lifting them up hard.
2. Front row: there are screws at the end of the slide, screw it down, slide hard to the end and come down; back row: there are two screws in the calf, screw it down and lift it up hard. As shown in the figure, there is a fixing bolt at the bottom of the seat. You can see the fixing screw when you lift the cover cloth. If you unscrew the screw, you can loosen the seat.
3. The disassembly method of Volkswagen Touareg seats, the seats are fixed with screws. To remove them, the owner needs to remove the screws. The front seat screw is located in front of the track. After removing it, the seat is pushed out. The rear seat screw is located in its calf position. Remove it and then lift the chair hard.
4. There is a pull strap in the middle of the rear seat. Pull the inside of the pull strap up, and the rear seat can be removed. After that, you can take off the rear seat. Take off the left hook on the rear seat.
5. The method of removing the rear seat of Volkswagen Touareg and Wu Baiwan is as follows: Open the trunk, find the lock under the seat, and press the lock. Lift the front of the seat to separate it from the bottom of the seat. Find the foot under the front end of the seat and rotate it in the direction of the arrow on the foot to separate it from the bottom of the seat.
The steps to disassemble the rear seat of the car are as follows. Find the wrench on both sides of the head of the rear seat and close to the window. Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion.Just install it in the reverse order of disassembly and installation.
First of all, you need to find the fixing bolts under the seat. These bolts are usually located on both sides of the bottom of the seat, and there may be one or more. Use a wrench or wrench kit to remove these bolts. If the bolts are tight, you can use lubricant or a slight force to loosen them. Next, the seat needs to be put down.
Disassemble the rear seat of Arizer 8 as follows: First, the owner needs to find the latches of the four safety seats on the rear seat of the car, and then gently pick off the lid on the latch.
The rear seat of the vehicle is not tight after being disassembled once, because the buckle of the seat is broken. If the buckle is broken, it needs to be replaced in the repair shop. The replacement price is about 100 yuan. Generally speaking, there will be three seats in the rear seat, and there are four snaps in total. When a snap is broken, the seat will not be too tight.
Disassembly method of the rear seat of the car: on both sides of the head of the rear seat, close to the window, there will be a handle, pull handle, the backrest of the rear seat can be turned forward, and most of the cushion position of the rear seat is directly squeezed to the rear of the car and lift it up.
Pull the wrench, the backrest of the rear seat can be turned forward, and the rear seat can be lifted up to remove the cushion, which can be installed in the reverse order of disassembly and installation. In order to have more operating space, the position of the front seat should be moved forward. It is best to open the buckle that fixes the seat headrest, and remove both the headrest and headrest.
Pharma active ingredients HS code checks
author: 2024-12-23 11:12HS code applications in compliance software
author: 2024-12-23 10:37HS code verification in Middle Eastern markets
author: 2024-12-23 10:32How to manage complex supply chains with data
author: 2024-12-23 10:28How to verify supplier credibility with data
author: 2024-12-23 09:20Customs broker performance analysis
author: 2024-12-23 09:54How to enhance supplier collaboration
author: 2024-12-23 09:51
HS code-based compliance in bilateral trades
266.49MB
Check
How to find ethical suppliers
788.34MB
Check
Steel pipes (HS code ) trade insights
225.17MB
Check
How to integrate trade data into workflows
323.57MB
Check
HS code-based trade data analytics
523.31MB
Check
How to integrate HS codes into BOMs
462.75MB
Check
Latin America trade data insights
794.69MB
Check
Industrial lubricants HS code classification
681.29MB
Check
HS code-driven supply chain benchmarking
423.21MB
Check
Global sourcing directories by HS code
319.36MB
Check
Electronics global shipment tracking
414.88MB
Check
Asia trade analytics platform
553.47MB
Check
USA trade data aggregation services
168.46MB
Check
Understanding HS codes in trade data
394.71MB
Check
Industry benchmarking via HS codes
792.35MB
Check
Industry-specific import regulation data
327.75MB
Check
How to benchmark import export performance
123.39MB
Check
HS code filtering for restricted items
821.53MB
Check
Food industry HS code classification
511.42MB
Check
Country-wise HS code compliance tips
438.88MB
Check
HS code-driven sectoral analysis
779.47MB
Check
How to reduce stockouts via trade data
388.22MB
Check
HS code alignment with import licensing
861.81MB
Check
Trade data-based price benchmarks
518.96MB
Check
Industry benchmarking via HS codes
161.38MB
Check
HS code-based container stowage planning
721.31MB
Check
HS code compliance for Nordic countries
551.62MB
Check
HS code-based forecasting for raw materials
136.57MB
Check
Global trade shipping route optimization
516.94MB
Check
Customs duty prediction models
568.88MB
Check
Import risk analysis metrics
366.41MB
Check
Global supply chain risk assessment
866.19MB
Check
Global trade intelligence newsletter
385.34MB
Check
HS code-based freight consolidation
193.33MB
Check
How to detect illicit trade patterns
768.11MB
Check
Latin America HS code compliance tips
136.18MB
Check
Scan to install
Industry-specific HS code database to discover more
Netizen comments More
2298 Import quota monitoring tools
2024-12-23 11:46 recommend
2040 Industry-specific trade growth forecasts
2024-12-23 11:29 recommend
2370 HS code-driven tariff reduction strategies
2024-12-23 11:17 recommend
2978 Sourcing opportunities filtered by HS code
2024-12-23 10:26 recommend
68 Machinery import clearance by HS code
2024-12-23 09:17 recommend