1. Delay The timing oil control valve of the camshaft controlled by the engine ECU is in the state shown in the figure below. The pressure oil enters the delay working cavity through the camshaft and blade, and the oil pressure pushes the blade and camshaft to rotate in the delayed direction of gas distribution.
2. Check the cylinder gasket, the water-blocking ring of the cylinder liner, the cylinder liner, the cylinder block. If these things are broken, they can cause water to enter the oil bottom. What often happens is the cylinder cushion and the water-blocking ring. Sometimes the engine is short of water and the cylinder head will suddenly explode after adding water and high temperature, and water will also enter the oil bottom. Please check it carefully.
3. Because the water itself has good fluidity and the water circulation speed in the cylinder is relatively fast, once the cylinder pad is damaged, the water in the waterway will flow into the oil channel, causing water to enter the oil span of the water-cooled engine. For normally used dry cylinder liner engines, damage to the cylinder pad is the primary cause of oil inlet, and sometimes the only reason.
1. If the whole car is mainly running at full load in the south, it is recommended to replace a 65° thermoster.
2. Insufficient coolant. Coolant leakage or lack of coolant will cause the engine water temperature to rise. At this time, we should check the coolant situation, ifInsufficient should be added to the appropriate position first, and then check whether the liquid level has dropped seriously in a few days. If so, we need to find the leakage location.
3. Check whether the antifreeze is missing, resulting in high engine water temperature. The circulation of the coolant, whether the circulation is not smooth. Secondly, it can also be checked that water temperature sensors, water pumps, thermosters, cooling fans, etc. can all lead to high water temperature. If your hands-on ability is not very strong, you'd better go to the repair shop for inspection.
4. Confirm whether your water temperature sensor or water temperature gauge is accurate. Can you tell me the specific model of your 6105? If it is a mechanical pump, reduce the injection angle to 2-5 degrees appropriately. If it is a common rail, you need to go to the service station for debugging.
5. After eliminating the radiator problem, it is necessary to check whether the engine thermosator is damaged (cannot be turned on);Check whether the water temperature sensor is falsely reported, whether the water pump belt is too loose, whether the water pump blades are damaged, etc.
It is the damage of the cylinder oil ring, and the spark plug electrode will be wrapped in oil that will not jump. The simple is to open the spark plug to see if Organic oil erosion, and the crankshaft sensor will also cause missing cylinders. Solution: Go to the 4s store to repair the engine.
Hello, if the high-pressure package is a one that controls 4 spark plugs, it is recommended to replace the high-pressure package. I hope it can help you [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Analysis problem: this appearsThe problem is usually caused by insufficient rigidity of the body, resulting in deformation of the vehicle while driving, friction or shaking between the door and the frame, or friction between the steel plates due to dewelding in some places.
After a cylinder is "frozen", if the speed of the gasoline engine decreases significantly, it means that the cylinder is working well; if the speed of the gasoline engine decreases very little, it means that the cylinder is not working normally; if the speed of each cylinder basically decreases, it is the same. This shows that each cylinder of the tested gasoline engine has good working uniformity.
1. If it is an engine with SCR, in principle, it is not possible not to add urea. When there is no urea, the alarm will be called, and the engine will be restricted from running.
2. Urea only treats exhaust gas and will not increase fuel consumption. The function of urea solution is to chemically react with nitrogen oxide compounds in the exhaust gas of sand tanks to produce non-toxic nitrogen and water, so as to reduce the emission of toxic gases in the exhaust gas of the car and reduce pollution.
3. Theoretically, it can run, but because there is no urea, the engine will limit the speed. Even if you step on the accelerator, you only have 40 yards in the end. Because the state's inspection of the national four cars is only for the household and the annual review, only to see if there is urea infusion.
4. Jianghuai's Guosi is not bad, isn't it? My new Shuailing is relatively satisfied with the power and fuel consumption. After the first warranty, there is no major problem. Be optimistic. Jianghuai Guosi has both technologies, but it seems that EGR is more. The configuration of the model is different from that of the model. You can go to the 4S store to have a look. Mine doesn't need to add urea.
1. For example: 5W40, 5 is the lowest applicable temperature of engine oil is minus 30 degrees, and W represents winter, indicating that engine oil is universal all year round. 40 is the high-temperature viscosity at 100 degrees.The larger the number, the more viscous the oil will be.
2. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
3. The engine model is the identification code compiled by the engine manufacturer for a batch of the same products in accordance with relevant regulations, enterprise or industry practices and the attributes of the engine. It is used to represent relevant information such as the manufacturer, specifications, performance, characteristics, processes, uses and product batches of the engine.
4. It is divided into several specifications, which is also the 6105 model. The reason for the different horsepower is that the compression ratio is different, and the position of the upper and lower stop points of the piston is different, which is the so-called high piston and low piston, and the fuel volume of the fuel injector is different.Product performance: YC160-8 is the latest 15-ton excavator launched by Yuchai Heavy Industry.
5. YC is Yuchai engine, CA is the abbreviation of FAW, WP is Weichai, and DL is really unclear.
1. In the diesel generator set R6105IZLD model, R stands for Ricardo, 6 stands for 6 cylinders, 105 stands for cylinder diameter, I stands for stroke, Z stands for supercharging, L stands for medium cooling, and D stands for power generation. Different diesel generator sets have different models, and their numbers and letters represent different meanings.
2. Hello, the code name of Yuchai 6105 engine is YC6J. Baidu search Yuchai official websiteIt can be seen that this model currently has five power segments of 180, 200, 2230 and 245 horsepower to choose from, and the output torque is between 650 and 890 Nm.
3. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
*Top trade research databases-APP, download it now, new users will receive a novice gift pack.
1. Delay The timing oil control valve of the camshaft controlled by the engine ECU is in the state shown in the figure below. The pressure oil enters the delay working cavity through the camshaft and blade, and the oil pressure pushes the blade and camshaft to rotate in the delayed direction of gas distribution.
2. Check the cylinder gasket, the water-blocking ring of the cylinder liner, the cylinder liner, the cylinder block. If these things are broken, they can cause water to enter the oil bottom. What often happens is the cylinder cushion and the water-blocking ring. Sometimes the engine is short of water and the cylinder head will suddenly explode after adding water and high temperature, and water will also enter the oil bottom. Please check it carefully.
3. Because the water itself has good fluidity and the water circulation speed in the cylinder is relatively fast, once the cylinder pad is damaged, the water in the waterway will flow into the oil channel, causing water to enter the oil span of the water-cooled engine. For normally used dry cylinder liner engines, damage to the cylinder pad is the primary cause of oil inlet, and sometimes the only reason.
1. If the whole car is mainly running at full load in the south, it is recommended to replace a 65° thermoster.
2. Insufficient coolant. Coolant leakage or lack of coolant will cause the engine water temperature to rise. At this time, we should check the coolant situation, ifInsufficient should be added to the appropriate position first, and then check whether the liquid level has dropped seriously in a few days. If so, we need to find the leakage location.
3. Check whether the antifreeze is missing, resulting in high engine water temperature. The circulation of the coolant, whether the circulation is not smooth. Secondly, it can also be checked that water temperature sensors, water pumps, thermosters, cooling fans, etc. can all lead to high water temperature. If your hands-on ability is not very strong, you'd better go to the repair shop for inspection.
4. Confirm whether your water temperature sensor or water temperature gauge is accurate. Can you tell me the specific model of your 6105? If it is a mechanical pump, reduce the injection angle to 2-5 degrees appropriately. If it is a common rail, you need to go to the service station for debugging.
5. After eliminating the radiator problem, it is necessary to check whether the engine thermosator is damaged (cannot be turned on);Check whether the water temperature sensor is falsely reported, whether the water pump belt is too loose, whether the water pump blades are damaged, etc.
It is the damage of the cylinder oil ring, and the spark plug electrode will be wrapped in oil that will not jump. The simple is to open the spark plug to see if Organic oil erosion, and the crankshaft sensor will also cause missing cylinders. Solution: Go to the 4s store to repair the engine.
Hello, if the high-pressure package is a one that controls 4 spark plugs, it is recommended to replace the high-pressure package. I hope it can help you [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Analysis problem: this appearsThe problem is usually caused by insufficient rigidity of the body, resulting in deformation of the vehicle while driving, friction or shaking between the door and the frame, or friction between the steel plates due to dewelding in some places.
After a cylinder is "frozen", if the speed of the gasoline engine decreases significantly, it means that the cylinder is working well; if the speed of the gasoline engine decreases very little, it means that the cylinder is not working normally; if the speed of each cylinder basically decreases, it is the same. This shows that each cylinder of the tested gasoline engine has good working uniformity.
1. If it is an engine with SCR, in principle, it is not possible not to add urea. When there is no urea, the alarm will be called, and the engine will be restricted from running.
2. Urea only treats exhaust gas and will not increase fuel consumption. The function of urea solution is to chemically react with nitrogen oxide compounds in the exhaust gas of sand tanks to produce non-toxic nitrogen and water, so as to reduce the emission of toxic gases in the exhaust gas of the car and reduce pollution.
3. Theoretically, it can run, but because there is no urea, the engine will limit the speed. Even if you step on the accelerator, you only have 40 yards in the end. Because the state's inspection of the national four cars is only for the household and the annual review, only to see if there is urea infusion.
4. Jianghuai's Guosi is not bad, isn't it? My new Shuailing is relatively satisfied with the power and fuel consumption. After the first warranty, there is no major problem. Be optimistic. Jianghuai Guosi has both technologies, but it seems that EGR is more. The configuration of the model is different from that of the model. You can go to the 4S store to have a look. Mine doesn't need to add urea.
1. For example: 5W40, 5 is the lowest applicable temperature of engine oil is minus 30 degrees, and W represents winter, indicating that engine oil is universal all year round. 40 is the high-temperature viscosity at 100 degrees.The larger the number, the more viscous the oil will be.
2. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
3. The engine model is the identification code compiled by the engine manufacturer for a batch of the same products in accordance with relevant regulations, enterprise or industry practices and the attributes of the engine. It is used to represent relevant information such as the manufacturer, specifications, performance, characteristics, processes, uses and product batches of the engine.
4. It is divided into several specifications, which is also the 6105 model. The reason for the different horsepower is that the compression ratio is different, and the position of the upper and lower stop points of the piston is different, which is the so-called high piston and low piston, and the fuel volume of the fuel injector is different.Product performance: YC160-8 is the latest 15-ton excavator launched by Yuchai Heavy Industry.
5. YC is Yuchai engine, CA is the abbreviation of FAW, WP is Weichai, and DL is really unclear.
1. In the diesel generator set R6105IZLD model, R stands for Ricardo, 6 stands for 6 cylinders, 105 stands for cylinder diameter, I stands for stroke, Z stands for supercharging, L stands for medium cooling, and D stands for power generation. Different diesel generator sets have different models, and their numbers and letters represent different meanings.
2. Hello, the code name of Yuchai 6105 engine is YC6J. Baidu search Yuchai official websiteIt can be seen that this model currently has five power segments of 180, 200, 2230 and 245 horsepower to choose from, and the output torque is between 650 and 890 Nm.
3. Different power: Yuchai 6105 has 135 horsepower, while 6108 has 160 horsepower, so the power values of these two models are different. Yuchai's 6105 is larger than 6108.
*Dynamic duty drawback calculations
author: 2024-12-23 11:24Trade finance structuring by HS code
author: 2024-12-23 11:16AI-driven trade data analytics
author: 2024-12-23 10:56HS code electrical machinery data
author: 2024-12-23 09:50Predictive container utilization analytics
author: 2024-12-23 10:56HS code automotive parts mapping
author: 2024-12-23 10:50Petroleum products HS code insights
author: 2024-12-23 10:02Global trade credit risk analysis
author: 2024-12-23 09:25743.49MB
Check397.54MB
Check949.93MB
Check569.79MB
Check484.25MB
Check411.16MB
Check771.54MB
Check457.74MB
Check147.44MB
Check619.47MB
Check356.84MB
Check238.83MB
Check586.57MB
Check966.86MB
Check629.54MB
Check434.47MB
Check517.67MB
Check466.96MB
Check636.57MB
Check554.48MB
Check519.77MB
Check787.85MB
Check128.17MB
Check387.33MB
Check149.19MB
Check297.71MB
Check387.89MB
Check479.24MB
Check365.21MB
Check471.94MB
Check754.97MB
Check884.21MB
Check429.68MB
Check325.54MB
Check195.56MB
Check899.72MB
CheckScan to install
Top trade research databases to discover more
Netizen comments More
1194 Dairy products HS code verification
2024-12-23 11:49 recommend
650 Organic textiles HS code verification
2024-12-23 11:23 recommend
1865 Livestock products HS code classification
2024-12-23 11:02 recommend
1478 Global trade customs valuation analysis
2024-12-23 10:18 recommend
1412 Pharma finished goods HS code references
2024-12-23 09:57 recommend