1. Primary FM: refers to the inherent ability of the frequency characteristics of the generator set speed control system to automatically adjust the frequency with the change of frequency. Secondary FM: refers to the FM method adopted when the primary FM cannot restore the frequency to the specified range when the power system load or power generation output changes significantly. Secondary FM is divided into manual FM and automatic FM.
2. Primary FM: refers to the ability inherent in the frequency characteristics of the speed regulation system of the generator set, which automatically adjusts the frequency with the change of frequency. It is characterized by fast frequency adjustment speed, but the adjustment amount varies with the generator set, and the adjustment amount is limited, which is difficult for the dispatcher on duty to control.
3. There is a differential adjustment of the first FM, and the frequency of the power grid is not maintained unchanged, which can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM. Only after secondary FM, the frequency of the power grid can accurately maintain a constant value.
The difference between primary FM and secondary FM is that the first FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, secondary FM is to accept intermediate commands or manual commands.
The primary FM is to participate in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.A FM is carried out by the speed regulation device, and the small FM range is fine tuning.
Secondary FM: refers to the FM method used when the primary FM cannot restore the frequency to the specified range when the load of the power system or power generation output changes significantly. Secondary FM is divided into manual FM and automatic FM.
The difference between primary FM and AGC is that their control objectives and adjustment ranges are different.
The primary FM refers to the FM carried out by the speed modulator of the generator, which transmits the original signal by changing the carrier frequency. In a FM, the amplitude of the original signal remains unchanged, but the different parts of the original signal are represented by changing the height of the carrier frequency.
1. [Answer]: C, D The power supply and load power of a stable power system must be dynamically balanced. When the power or load of the power supply changes (take insufficient power as an example), the frequency of the system will be reduced, and the load equipment in the system will affect its active absorption due to the decrease in frequency.
2. The power balance factor is related. The frequency of the power system is affected by the power balance. We know that alternating current cannot be stored, so we can use as much as we send, and the active power emitted and the active power consumed are balanced.
3. The basic principle of primary FM of the power system: the frequency of the power grid is determined by the power generation power and the power consumption load. When the power generation power is equal to the power consumption, the power grid frequency is stable;When the power generation power is greater than the power consumption load, the frequency of the power grid increases; when the power generation power is less than the power consumption load, the frequency of the power grid decreases.
4. Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
FM refers to the FM of the generator's speed regulation, which transmits the original signal by changing the carrier frequency. In a FM, the amplitude of the original signal remains unchanged, but the different parts of the original signal are represented by changing the height of the carrier frequency.
The difference between primary FM and secondary FM is that primary FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.
Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
Primary FM and secondary FM are two important FM modes in the power system, which are used to maintain the stability of the system frequency. One-time FMIt means that when the load of the power system changes, the generator set automatically adjusts the output to quickly respond to the load change and suppress the initial shift of the system frequency.
Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
The difference between primary FM and secondary FM is that primary FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.
1The basic principle of primary FM of the power system: the frequency of the power grid is determined by the size of the power generation power and the power consumption load. When the power generation power is equal to the power consumption, the frequency of the power grid is stable; when the power generation power is greater than the power consumption load, the frequency of the power grid increases; when the power generation power is less than the power consumption load, the frequency of the power grid decreases.
2. Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, but can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
3. Primary FM: refers to the inherent ability of the frequency characteristics of the generator set speed regulation system to automatically adjust the frequency with the change of frequency. Secondary FM: refers to the FM method adopted when the primary FM cannot restore the frequency to the specified range when the power system load or power generation output changes significantly.Secondary FM is divided into manual FM and automatic FM.
4. A FM is a regulation mechanism of the power system, which is used to maintain the stability of the system frequency. When the load in the system changes, a FM will adjust the output of the generator set to offset the impact of load changes on the system frequency.
5. Primary FM refers to the inherent ability of the frequency characteristics of the speed regulation system of the generator set, which automatically adjusts the frequency with the change of frequency. It is characterized by fast frequency adjustment speed, but the adjustment amount varies with the generator set, and the adjustment amount is limited, which is difficult for the dispatcher on duty to control.
6. Frequency adjustment, also known as frequency control, is the main measure to maintain the balance of active power supply and demand in the power system. Its fundamental purpose is to ensure the frequency stability of the power system. The main methods of frequency adjustment of the power system are to adjust the power generation power and load management.
Who knows what a FM is? What is secondary FM?How to identify export-ready products-APP, download it now, new users will receive a novice gift pack.
1. Primary FM: refers to the inherent ability of the frequency characteristics of the generator set speed control system to automatically adjust the frequency with the change of frequency. Secondary FM: refers to the FM method adopted when the primary FM cannot restore the frequency to the specified range when the power system load or power generation output changes significantly. Secondary FM is divided into manual FM and automatic FM.
2. Primary FM: refers to the ability inherent in the frequency characteristics of the speed regulation system of the generator set, which automatically adjusts the frequency with the change of frequency. It is characterized by fast frequency adjustment speed, but the adjustment amount varies with the generator set, and the adjustment amount is limited, which is difficult for the dispatcher on duty to control.
3. There is a differential adjustment of the first FM, and the frequency of the power grid is not maintained unchanged, which can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM. Only after secondary FM, the frequency of the power grid can accurately maintain a constant value.
The difference between primary FM and secondary FM is that the first FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, secondary FM is to accept intermediate commands or manual commands.
The primary FM is to participate in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.A FM is carried out by the speed regulation device, and the small FM range is fine tuning.
Secondary FM: refers to the FM method used when the primary FM cannot restore the frequency to the specified range when the load of the power system or power generation output changes significantly. Secondary FM is divided into manual FM and automatic FM.
The difference between primary FM and AGC is that their control objectives and adjustment ranges are different.
The primary FM refers to the FM carried out by the speed modulator of the generator, which transmits the original signal by changing the carrier frequency. In a FM, the amplitude of the original signal remains unchanged, but the different parts of the original signal are represented by changing the height of the carrier frequency.
1. [Answer]: C, D The power supply and load power of a stable power system must be dynamically balanced. When the power or load of the power supply changes (take insufficient power as an example), the frequency of the system will be reduced, and the load equipment in the system will affect its active absorption due to the decrease in frequency.
2. The power balance factor is related. The frequency of the power system is affected by the power balance. We know that alternating current cannot be stored, so we can use as much as we send, and the active power emitted and the active power consumed are balanced.
3. The basic principle of primary FM of the power system: the frequency of the power grid is determined by the power generation power and the power consumption load. When the power generation power is equal to the power consumption, the power grid frequency is stable;When the power generation power is greater than the power consumption load, the frequency of the power grid increases; when the power generation power is less than the power consumption load, the frequency of the power grid decreases.
4. Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
FM refers to the FM of the generator's speed regulation, which transmits the original signal by changing the carrier frequency. In a FM, the amplitude of the original signal remains unchanged, but the different parts of the original signal are represented by changing the height of the carrier frequency.
The difference between primary FM and secondary FM is that primary FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.
Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
Primary FM and secondary FM are two important FM modes in the power system, which are used to maintain the stability of the system frequency. One-time FMIt means that when the load of the power system changes, the generator set automatically adjusts the output to quickly respond to the load change and suppress the initial shift of the system frequency.
Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, and can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
The difference between primary FM and secondary FM is that primary FM participates in the frequency adjustment of the power grid, with a certain amplitude limit and dead zone, and the secondary FM is to accept intermediate modulation commands or manual instructions.
1The basic principle of primary FM of the power system: the frequency of the power grid is determined by the size of the power generation power and the power consumption load. When the power generation power is equal to the power consumption, the frequency of the power grid is stable; when the power generation power is greater than the power consumption load, the frequency of the power grid increases; when the power generation power is less than the power consumption load, the frequency of the power grid decreases.
2. Secondary FM: Primary FM has differential adjustment, which cannot maintain the frequency of the power grid unchanged, but can only mitigate the degree of change of the frequency of the power grid. Therefore, it is also necessary to use synchronizers to increase and slow down the load of certain units to restore the frequency of the power grid. This process is called secondary FM.
3. Primary FM: refers to the inherent ability of the frequency characteristics of the generator set speed regulation system to automatically adjust the frequency with the change of frequency. Secondary FM: refers to the FM method adopted when the primary FM cannot restore the frequency to the specified range when the power system load or power generation output changes significantly.Secondary FM is divided into manual FM and automatic FM.
4. A FM is a regulation mechanism of the power system, which is used to maintain the stability of the system frequency. When the load in the system changes, a FM will adjust the output of the generator set to offset the impact of load changes on the system frequency.
5. Primary FM refers to the inherent ability of the frequency characteristics of the speed regulation system of the generator set, which automatically adjusts the frequency with the change of frequency. It is characterized by fast frequency adjustment speed, but the adjustment amount varies with the generator set, and the adjustment amount is limited, which is difficult for the dispatcher on duty to control.
6. Frequency adjustment, also known as frequency control, is the main measure to maintain the balance of active power supply and demand in the power system. Its fundamental purpose is to ensure the frequency stability of the power system. The main methods of frequency adjustment of the power system are to adjust the power generation power and load management.
Who knows what a FM is? What is secondary FM?HS code-driven market entry strategy
author: 2024-12-23 11:56HS code-based supplier development
author: 2024-12-23 10:53Data-driven export licensing compliance
author: 2024-12-23 10:43Real-time import export alerts
author: 2024-12-23 10:11Customized market entry reports
author: 2024-12-23 09:23Optimizing tariff schedules by HS code
author: 2024-12-23 11:57Global trade compliance certifications
author: 2024-12-23 11:31Global HS code data enrichment services
author: 2024-12-23 11:23How to validate supplier compliance
author: 2024-12-23 09:42388.13MB
Check461.53MB
Check253.95MB
Check643.93MB
Check765.45MB
Check127.72MB
Check185.28MB
Check275.53MB
Check289.98MB
Check513.87MB
Check235.99MB
Check763.68MB
Check974.92MB
Check112.89MB
Check244.71MB
Check575.73MB
Check282.31MB
Check631.32MB
Check947.37MB
Check911.21MB
Check334.78MB
Check549.31MB
Check429.68MB
Check713.59MB
Check153.27MB
Check611.84MB
Check627.26MB
Check547.68MB
Check694.57MB
Check198.84MB
Check554.25MB
Check433.77MB
Check355.28MB
Check538.28MB
Check587.51MB
Check986.22MB
CheckScan to install
How to identify export-ready products to discover more
Netizen comments More
1057 Ceramic tiles HS code classification
2024-12-23 11:18 recommend
1199 Data-driven multimodal transport decisions
2024-12-23 10:45 recommend
1284 CIS countries HS code usage patterns
2024-12-23 09:34 recommend
1635 Trade data for resource allocation
2024-12-23 09:33 recommend
983 Best global trade intelligence for SMEs
2024-12-23 09:15 recommend