1. After all the wiring connections of the anti-theft device host are completed, the decorative board should be debugged before installing. Check whether each wiring plug is in contact with the host socket and tight, and whether there is any looseness.
2. Installation method and precautions of the anti-theft device x0dx0a preparations x0dx0a tools x0dx0a wire stripping pliers, electric measuring pen (12V-24V), screwdriver (cross, one character), insulating tape, tool knife, double-sided adhesive, tie, and some other disassembly tools ( It depends on the specific model).
3. Wiring requirements: the connector should be tightly connected, avoid virtual connection, and wrap it with insulating tape. This process is the most important step in the whole installation process. If the connection is wrong, the anti-theft device cannot be used in the light, and the components in the car will be burned, making the vehicle unable to use normally or even causing a fire.
Where is the car alarm installed?&Mdash The procedure for installing the anti-theft alarm First check the condition of the car: such as battery voltage, water temperature gauge, oil gauge, headlights, small lights, turn signals, brake lights, indoor lights, airbag lights, ABS lights, SRS, sunroof, etc.
Car anti-theft alarms are generally installed in the dashboard of the cab, mainly equipped with the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
The installation location requirements of different types of car anti-theft alarms are different: wired car anti-theft alarms can generally be considered to be installed under the dashboard or under the driver's seat. If only the positioning function is installed, roof lights, side doors, taillights and many other places can also be considered.
The steps for installing the car anti-theft device are as follows: In the connection of the circuit breaker, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked to the upper end of the disconnection circuit.
Notes: 1) The installation of the anti-theft lock should be in place. It is best to keep the lock core parallel to the body floor, and the closer it is to the fixture in the car, the better. 2) Use anti-theft alarm and car anti-theft lock at the same time to prevent theft, which has a better anti-theft effect. 3) If the anti-theft system fails, don't disassemble it by yourself. You should go to a professional repair shop to deal with it.
1. The steps to install the car anti-theft device are as follows: power offIn the connection of the device, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked at the upper end of the disconnection circuit.
2. Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
3. Before installing the anti-theft alarm, check the original car circuit: start the circuit: turn the car key to the ON position and observe the lighting of each indicator light (such as airbag, ABS, charging, engine fault light, etc.) in the dashboard.), then start the vehicle normally, and then observe whether each indicator light Abnormally extinguished.
The car anti-theft alarm is generally installed in the dashboard of the cab, mainly installing the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
Installation: Find the +12V normal fire line, negative electricity (iron), turn signal line, door edge line, brake line, start motor line, central control line, on/off signal line, etc. to be connected.After checking and installing, you must self-check whether all functions of the vehicle are normal, and then put the removed trim panel back into its original own.
How to install the car burglar alarm? In the connection of the circuit breaker, it is necessary to confirm the ignition line, the fuel pump adjustment line and the starter line, and then choose which way to disconnect (when the starter line is disconnected, there is no anti-robb function); the anti-theft input on the host line should be connected to the upper end of the disconnection circuit. You can also pick up the car separately.
How to find niche import markets-APP, download it now, new users will receive a novice gift pack.
1. After all the wiring connections of the anti-theft device host are completed, the decorative board should be debugged before installing. Check whether each wiring plug is in contact with the host socket and tight, and whether there is any looseness.
2. Installation method and precautions of the anti-theft device x0dx0a preparations x0dx0a tools x0dx0a wire stripping pliers, electric measuring pen (12V-24V), screwdriver (cross, one character), insulating tape, tool knife, double-sided adhesive, tie, and some other disassembly tools ( It depends on the specific model).
3. Wiring requirements: the connector should be tightly connected, avoid virtual connection, and wrap it with insulating tape. This process is the most important step in the whole installation process. If the connection is wrong, the anti-theft device cannot be used in the light, and the components in the car will be burned, making the vehicle unable to use normally or even causing a fire.
Where is the car alarm installed?&Mdash The procedure for installing the anti-theft alarm First check the condition of the car: such as battery voltage, water temperature gauge, oil gauge, headlights, small lights, turn signals, brake lights, indoor lights, airbag lights, ABS lights, SRS, sunroof, etc.
Car anti-theft alarms are generally installed in the dashboard of the cab, mainly equipped with the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
The installation location requirements of different types of car anti-theft alarms are different: wired car anti-theft alarms can generally be considered to be installed under the dashboard or under the driver's seat. If only the positioning function is installed, roof lights, side doors, taillights and many other places can also be considered.
The steps for installing the car anti-theft device are as follows: In the connection of the circuit breaker, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked to the upper end of the disconnection circuit.
Notes: 1) The installation of the anti-theft lock should be in place. It is best to keep the lock core parallel to the body floor, and the closer it is to the fixture in the car, the better. 2) Use anti-theft alarm and car anti-theft lock at the same time to prevent theft, which has a better anti-theft effect. 3) If the anti-theft system fails, don't disassemble it by yourself. You should go to a professional repair shop to deal with it.
1. The steps to install the car anti-theft device are as follows: power offIn the connection of the device, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked at the upper end of the disconnection circuit.
2. Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
3. Before installing the anti-theft alarm, check the original car circuit: start the circuit: turn the car key to the ON position and observe the lighting of each indicator light (such as airbag, ABS, charging, engine fault light, etc.) in the dashboard.), then start the vehicle normally, and then observe whether each indicator light Abnormally extinguished.
The car anti-theft alarm is generally installed in the dashboard of the cab, mainly installing the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
Installation: Find the +12V normal fire line, negative electricity (iron), turn signal line, door edge line, brake line, start motor line, central control line, on/off signal line, etc. to be connected.After checking and installing, you must self-check whether all functions of the vehicle are normal, and then put the removed trim panel back into its original own.
How to install the car burglar alarm? In the connection of the circuit breaker, it is necessary to confirm the ignition line, the fuel pump adjustment line and the starter line, and then choose which way to disconnect (when the starter line is disconnected, there is no anti-robb function); the anti-theft input on the host line should be connected to the upper end of the disconnection circuit. You can also pick up the car separately.
How to handle multi-currency billing
author: 2024-12-23 11:01Australia HS code tariff insights
author: 2024-12-23 10:59Sustainable trade data analytics
author: 2024-12-23 10:53How to measure supplier performance
author: 2024-12-23 10:51Dynamic supplier inventory analysis
author: 2024-12-23 10:36Textile exports HS code breakdown
author: 2024-12-23 11:32USA customs data analysis services
author: 2024-12-23 10:44HS code-based invoice validation
author: 2024-12-23 10:28HS code segmentation for industrial chemicals
author: 2024-12-23 09:22986.59MB
Check122.43MB
Check762.18MB
Check115.93MB
Check887.82MB
Check418.16MB
Check411.44MB
Check862.88MB
Check193.85MB
Check733.17MB
Check446.82MB
Check434.35MB
Check871.55MB
Check345.41MB
Check854.18MB
Check368.19MB
Check182.39MB
Check866.84MB
Check729.92MB
Check659.81MB
Check479.53MB
Check864.22MB
Check313.75MB
Check291.82MB
Check448.64MB
Check931.68MB
Check556.11MB
Check392.33MB
Check442.11MB
Check779.18MB
Check243.17MB
Check654.31MB
Check936.29MB
Check637.36MB
Check617.54MB
Check618.62MB
CheckScan to install
How to find niche import markets to discover more
Netizen comments More
2061 Trade data for construction materials
2024-12-23 11:58 recommend
83 Trade data for metal commodities
2024-12-23 11:49 recommend
985 HS code-driven supplier performance metrics
2024-12-23 10:51 recommend
2720 HS code-led regulatory frameworks
2024-12-23 10:31 recommend
786 Global trade customs valuation analysis
2024-12-23 09:47 recommend