Enhanced due diligence via HS code

List of contents of this article:

• 1. Reinstall computer win7 card in logo interface
• 2, What to do if the reinstall system is stuck in the installation interface
• 3、What to do if the computer reinstalls the system is stuck
• 4、 What should I do if the computer is still stuck in the boot interface after reinstalling the system?

Reinstall the computer win7 card in the logo interface

1. Press the F2 key or DEL key when booting to enter the BIOS system; Note: The machine model is different, enter The keys of the BIOS may be different. For details, please refer to the screen prompt in the lower left corner.

2. It may be a hardware failure. If the hard disk is still invalid after replacing the data cable, you can also try to unplug the data cable of the hard disk first, and then turn on the power test to see if it will still be stuck on the LOGO screen. If not, it is estimated that it is a hard disk failure, and the solution is to replace it. The hard disk.

3. Computer poisoning or malware may also cause computer abnormalities. The solution is to upgrade the anti-virus software and anti-virus. If it really doesn't work, reinstall or restore the system. Reinstalling or restoring the system can completely solve software problems.

4. The solution to the problem of being stuck in the boot interface after reinstalling the win7 system: First of all, you can see if the reason for the failure is caused by starting acpi. Try to restart the computer, and then press F11 to enter the BIOS before the system has not been started. Next Disable ACPI, and then restart the computer again.

What to do when reinstalling the system stuck in the installation interface

solution, re-download, download it to other system websites.There are bad channels on the installation disk. Whether it is installed with a USB flash drive, CD-ROM, or hard disk, there may be bad channels, causing the installation to be stuck.

Search for answers. I want to ask a question. Baidu knows the prompt information and knows that the baby can't find the question_! The problem may have been invalidated.

First, restart the computer, hold down the "Shift" key on the keyboard 2, and then select "View Advanced Repair Options", "Troubleshooting", "Advanced Options", "Startup Settings" 3 in the new interface, and then click the "Restart" option in the lower right corner. Press "F4" on the security interface after restarting to enter the security mode. Type 4 enters the safety model.

The method is as follows: 1 First, press and hold the shutdown for 10 seconds, and then the system will automatically repair it. Then enter the security interface and select "Difficult Solution". After entering, you will first see "Reset thisComputer" 2 Click to reset this computer, and you will see the following interface. According to your own needs, select "Whether to keep the installed software, applications and materials".

Now I will share with you the specific solution to get stuck in the Starting Windows interface when installing the win7 system. Recommendation: First, try to disable ACPI in BIOS to solve the problem.

The computer graphics card or memory is too small to operate normally. Replace the computer memory stick; reinstall the system; the computer system and the computer cannot be installed normally without access, and the system disk needs to be replaced for reinstallation; the computer system installation and decompression process is relatively slow, need to wait patiently, Just wait for the installation.

What to do if the computer is reinstalled and the system gets stuck

1. Restart the computer. First, try to restart the computer, and then continue to install the system. Usually, this can solve the problem. If the restart is invalid after replacing the system disk, you can consider replacing another version of the system disk for installation, which may have unexpected effects.

2. Solution: Disassemble the computer and take it to a special maintenance site for repair. Generally, the maintenance fee for replacing the capacitor of the motherboard power supply is within 20 yuan (the cost is only a few cents); if it exceeds this number, you will encounter JS.

3. There is no choice but to press the reset key to restart the computer. Because the computer was previously equipped with a one-click GHOST backup, I tried to restore it decisively, but it was still the same after the restoration.

4. The computer reinstalled the system and has been stuck there. There are the following reasons and solutions.If the system image file is incomplete or damaged, it may not be downloaded completely when downloading, or the file is damaged when downloading, so that it will be stuck during installation. The solution is to re-download and download it to other system websites.

5. Enter safe mode: restart the computer and press the F8 key during the boot process to enter the advanced boot option. Select "Safe Mode" and press Enter. In safe mode, you can try to run the system's built-in troubleshooting tool to fix the startup problem.

What should I do if the computer is still stuck in the boot interface after reinstalling the system?

1. Search for the answer. I want to ask a question. Baidu knows the prompt information and the baby can't find the question_! The problem may have been invalidated.

2. Force shutdown: Press and hold the power button of the computer for about 5 seconds until the computer is completely shut down. Then restart the computer to see if it can enter the system.

3. Therefore, if the computer cannot enter the desktop after turning on after replacing the system and has been on the boot interface, you can try the following methods: check the system installationWhether it is complete: You can check whether the system is installed completely. If not, you can reinstall it.

4. Usually, it can be solved by replacing a system version and reinstalling it; 2: The hard disk has a bad channel, causing the system to be unable to read and write data normally. In this case, it needs to be solved by repairing the hard disk or replacing a new hard disk. It is known from a large number of installation experiences that most of these failures are caused by the instability of the system version, which can be solved by replacing the system version.