Connect the new hard disk to the computer; download and install the partition assistant (free software); start the partition assistant program, (1) click the system disk of the original hard disk, (2) click [migrate system to firmware] on the left side of the window State drive], (3) Click: Next in the open window.
When booting, there is a prompt in the lower right corner of the screen. Now the new motherboard does not need to enter the BIOS to set the computer to start from the CD-ROM. For example, the Gigabyte motherboard can be turned on and press F12 to choose to start from the CD-ROM.
Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk. If you are the old masterBoard, it will take a little effort. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
1. Use GPT partition mode to partition 3TB hard disk: open DiskGenius tool, first click to select the 3T hard disk, then click "Quick Partition" at the top, and then remember to select the GPT format (GUID) in the partition table type as shown in the figure below.
2. Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk.If you are an old motherboard, you will have to work harder. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
3. The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area. Then use GHOST to restore to the system partition, and then repair the boot to start the system.
4. In the figure, the 3T hard disk is used as a system disk (the hard disk that installs the operating system). 2: When the hard disk larger than 2T is used as a system disk, when the bios is booted to Legacy (traditional boot) and the partition mode is MBR, the MBR partition cannot manage a capacity of more than 2T, and can only be idle.
1. Maybe your hard disk boot area Problem, or there is a problem with the system. Plug in the cable inside the machine, (including hard disk, optical drive power supply and data cable) board card, wipe off the golden finger of the card, and clear the dust. Enter COMS to restore the factory settings.
2. If the system can be installed, then there is no problem with the hardware, so either it is a problem with the installation of the operating system or the BIOS settings do not match the system.
3. The system boot sector is lost. Solution: Insert the PE boot disk to enterPE desktop, use partition software to rebuild mbr, and then use system boot repair software to rebuild system boot. The hard disk is loose, the interface is closed for some reason or the startup item of the hard disk is deleted, resulting in the device not being recognized.
1. The speed of the monitoring dedicated hard disk is much slower than that of the computer, and it cannot be used as a system disk. If it is no problem at all as a warehouse disk, it will not have any impact on the computer. It's just that the monitoring hard disk is slow and slow when reading data.
2. If the removed monitoring hard disk is added to the ordinary desktop, it cannot be recognized, because the ordinary desktop cannot load the system of this hard disk.
3. This can be calculated. It depends on how high the bit rate you set the DVR video. Generally, the maximum video effect of DVR is 512K, and you can choose it yourself, 64K, 128K, 256K, etc. There are also miscellaneous DVRs that cannot be selected, generally 128K.
4. Finally, it can be used! Method 3: Install the system (take the installation of WINDOWS XP as an example below) I chose a complete Windows XP installation CD without any cracks.
5. The monitored hard disk is also a conventional mechanical hard disk. It can be used directly, just use the previous partition format. If you want to use the main disk, you need to install an operating system.
6, Configuration--SATIn A-Operation, you can see that the hard disk mode is RAID On. After selecting the AHCI mode and pressing F10 to save and restart, the 3T large hard disk can be recognized normally. It is recommended to use diskgenius software to split the disk, and the Disk management that comes with Windows may not be fully allocated.
1. The system image file is damaged: If there is a problem with your image file, an error will be prompted in the process of copying the image file, and the system cannot be installed. You need to re-download the mirror image (ISO) file.
2. There are two main reasons why the hard disk cannot install the operating system: hard disk problems and setting problems. The problems of the hard disk include the wrong partition format, the hard disk cannot be recognized by the motherboard, and the hard disk itself is damaged. THE SETTING PROBLEMS ARE MAINLY THE SETTINGS OF SATA MODE (USUALLY IN ACHI MODE, THE WIN XP SYSTEM CANNOT BE INSTALLED OR USED) AND THE HARD DISK ERROR SELECTED DURING INSTALLATION.
3. The old motherboard BIOS does not support UEFI startup. You have to consider getting a hard disk installation system of less than 2TB to start.If you want the old motherboard to support 3TB hard disk startup, the operation is very complicated and may not be successful. To be honest, it is better to use a hard disk within 2T as a system disk, which is more practical.
win7 must use the 64-bit version and integrate the UEFI module.
The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area.Then use GHOST to restore to the system partition, and then repair the boot to start the system.
Install the system win7: Preparation: 1 Make a USB boot disk.
Win7 64-bit system can support reading and writing of GPT disk and booting from GPT disk with the support of UEFI. You can use Diskgenius or Partition Assistant to establish the disk as a GPT partition table disk and then partition it. There is no logical partition on the GPT disk, and all of them are the main partition.
No, it usually needs to be installed with auxiliary tools. Because the system mirror file itself cannot be run. You can reinstall the win7 system with a USB flash drive: make a boot disk.
HS code-driven risk management frameworks-APP, download it now, new users will receive a novice gift pack.
Connect the new hard disk to the computer; download and install the partition assistant (free software); start the partition assistant program, (1) click the system disk of the original hard disk, (2) click [migrate system to firmware] on the left side of the window State drive], (3) Click: Next in the open window.
When booting, there is a prompt in the lower right corner of the screen. Now the new motherboard does not need to enter the BIOS to set the computer to start from the CD-ROM. For example, the Gigabyte motherboard can be turned on and press F12 to choose to start from the CD-ROM.
Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk. If you are the old masterBoard, it will take a little effort. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
1. Use GPT partition mode to partition 3TB hard disk: open DiskGenius tool, first click to select the 3T hard disk, then click "Quick Partition" at the top, and then remember to select the GPT format (GUID) in the partition table type as shown in the figure below.
2. Your motherboard supports UEFI bios and adopts GPT format disk, that is, the GUID partition table. The installation system is no different from a small hard disk.If you are an old motherboard, you will have to work harder. The traditional BIOS+mbr partition table can only use 2TB hard disk, and the remaining space cannot be used.
3. The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area. Then use GHOST to restore to the system partition, and then repair the boot to start the system.
4. In the figure, the 3T hard disk is used as a system disk (the hard disk that installs the operating system). 2: When the hard disk larger than 2T is used as a system disk, when the bios is booted to Legacy (traditional boot) and the partition mode is MBR, the MBR partition cannot manage a capacity of more than 2T, and can only be idle.
1. Maybe your hard disk boot area Problem, or there is a problem with the system. Plug in the cable inside the machine, (including hard disk, optical drive power supply and data cable) board card, wipe off the golden finger of the card, and clear the dust. Enter COMS to restore the factory settings.
2. If the system can be installed, then there is no problem with the hardware, so either it is a problem with the installation of the operating system or the BIOS settings do not match the system.
3. The system boot sector is lost. Solution: Insert the PE boot disk to enterPE desktop, use partition software to rebuild mbr, and then use system boot repair software to rebuild system boot. The hard disk is loose, the interface is closed for some reason or the startup item of the hard disk is deleted, resulting in the device not being recognized.
1. The speed of the monitoring dedicated hard disk is much slower than that of the computer, and it cannot be used as a system disk. If it is no problem at all as a warehouse disk, it will not have any impact on the computer. It's just that the monitoring hard disk is slow and slow when reading data.
2. If the removed monitoring hard disk is added to the ordinary desktop, it cannot be recognized, because the ordinary desktop cannot load the system of this hard disk.
3. This can be calculated. It depends on how high the bit rate you set the DVR video. Generally, the maximum video effect of DVR is 512K, and you can choose it yourself, 64K, 128K, 256K, etc. There are also miscellaneous DVRs that cannot be selected, generally 128K.
4. Finally, it can be used! Method 3: Install the system (take the installation of WINDOWS XP as an example below) I chose a complete Windows XP installation CD without any cracks.
5. The monitored hard disk is also a conventional mechanical hard disk. It can be used directly, just use the previous partition format. If you want to use the main disk, you need to install an operating system.
6, Configuration--SATIn A-Operation, you can see that the hard disk mode is RAID On. After selecting the AHCI mode and pressing F10 to save and restart, the 3T large hard disk can be recognized normally. It is recommended to use diskgenius software to split the disk, and the Disk management that comes with Windows may not be fully allocated.
1. The system image file is damaged: If there is a problem with your image file, an error will be prompted in the process of copying the image file, and the system cannot be installed. You need to re-download the mirror image (ISO) file.
2. There are two main reasons why the hard disk cannot install the operating system: hard disk problems and setting problems. The problems of the hard disk include the wrong partition format, the hard disk cannot be recognized by the motherboard, and the hard disk itself is damaged. THE SETTING PROBLEMS ARE MAINLY THE SETTINGS OF SATA MODE (USUALLY IN ACHI MODE, THE WIN XP SYSTEM CANNOT BE INSTALLED OR USED) AND THE HARD DISK ERROR SELECTED DURING INSTALLATION.
3. The old motherboard BIOS does not support UEFI startup. You have to consider getting a hard disk installation system of less than 2TB to start.If you want the old motherboard to support 3TB hard disk startup, the operation is very complicated and may not be successful. To be honest, it is better to use a hard disk within 2T as a system disk, which is more practical.
win7 must use the 64-bit version and integrate the UEFI module.
The system with the installed version can be installed directly. If your motherboard supports UEFI booting, you can also install it with GHOST, partition the hard disk into GPT format, divide the ESP and MSR partitions, and then install the system in another area.Then use GHOST to restore to the system partition, and then repair the boot to start the system.
Install the system win7: Preparation: 1 Make a USB boot disk.
Win7 64-bit system can support reading and writing of GPT disk and booting from GPT disk with the support of UEFI. You can use Diskgenius or Partition Assistant to establish the disk as a GPT partition table disk and then partition it. There is no logical partition on the GPT disk, and all of them are the main partition.
No, it usually needs to be installed with auxiliary tools. Because the system mirror file itself cannot be run. You can reinstall the win7 system with a USB flash drive: make a boot disk.
Advanced trade route cost analysis
author: 2024-12-23 11:08Cross-verifying suppliers by HS code
author: 2024-12-23 10:11Agricultural machinery HS code lookups
author: 2024-12-23 10:05Tariff reduction opportunity analysis
author: 2024-12-23 09:14HS code-based inventory forecasting
author: 2024-12-23 08:52Processed foods HS code mapping
author: 2024-12-23 10:48HS code mapping in government tenders
author: 2024-12-23 10:37Global supply chain risk assessment
author: 2024-12-23 10:16Pharma excipients HS code classification
author: 2024-12-23 09:28Carbon steel HS code references
author: 2024-12-23 09:01795.88MB
Check453.54MB
Check361.55MB
Check446.67MB
Check323.87MB
Check386.63MB
Check796.55MB
Check958.95MB
Check172.88MB
Check979.83MB
Check629.84MB
Check945.76MB
Check888.38MB
Check962.35MB
Check496.44MB
Check485.99MB
Check668.58MB
Check742.58MB
Check719.76MB
Check717.52MB
Check614.94MB
Check472.79MB
Check438.84MB
Check284.64MB
Check689.93MB
Check713.77MB
Check344.21MB
Check166.58MB
Check767.95MB
Check263.97MB
Check137.74MB
Check878.16MB
Check923.84MB
Check794.16MB
Check892.23MB
Check815.11MB
CheckScan to install
HS code-driven risk management frameworks to discover more
Netizen comments More
349 Tariff impact simulation tools
2024-12-23 10:51 recommend
516 HS code-driven cross-border e-commerce
2024-12-23 10:49 recommend
2852 Top trade data APIs for developers
2024-12-23 09:49 recommend
2532 international trade research
2024-12-23 09:29 recommend
482 HS code-based reclassification services
2024-12-23 09:05 recommend