1. The shaking when the car starts is the gearbox Question. This kind of failure is generally more common in manual transmission models.
2. The common reason for car start-up jitter is that the throttle valve is too dirty or the fuel injector has too much carbon.When the engine accumulates too much carbon, the gasoline sprayed by the fuel injector head during cold start will be absorbed by a large amount of carbon accumulation, resulting in excessive mixing gas during cold start and difficulty in starting.
3. This kind of jitter may be caused by indentation when the transmission gear and the transmission shaft mesh. This problem may exist in many powershift models, while AT and CVT models usually do not tremble when starting. Automatic manual transmission models such as DSG and DCT may tremble when changing gears.
1. The engine foot shakes. The automatic transmission car shakes badly when it is in the forward gear but has not started. It is likely that the engine foot has failed. In the process of using the car, the wear rate of the engine foot is much higher than that of other parts. After a long time or the engine foot Deformation and other problems may occur in certain quality defects.
2. This kind of jitter may be caused by indentation when the transmission gear meshes with the transmission shaft. This problem may exist in many powershift models, while AT and CVT models usually do not tremble when starting.Automatic manual transmission models such as DSG and DCT may tremble when changing gears.
3. Serious engine carbonization: Cars always have the problem of carbonization, including cylinder carbonization, throttle carbonisation, spark plug carbonation, intake carbonation, etc. When the engine accumulates too much carbon, it will affect the ignition energy, intake efficiency and air-fuel ratio of the car, resulting in unstable power output of the car, idling and acceleration jitter.
Solution: Check the oil pressure and replace the parts if necessary. Aging of engine parts. Car jitter is also related to the aging of engine feet (also known as claw pads).
When judging, set up the drive first.Bridge, plug the front wheel with safety plugs, start the engine and gradually change to high-speed gear, so that the drive wheel reaches the final test vibration speed. If the car body and the steering wheel shake at this time, it is the vibration caused by the transmission system.
It is relatively simple to solve this problem. You only need to replace the aging foot mat. It is recommended that the car owner choose the original accessories when replacing the foot mat.
Refined metals HS code references-APP, download it now, new users will receive a novice gift pack.
1. The shaking when the car starts is the gearbox Question. This kind of failure is generally more common in manual transmission models.
2. The common reason for car start-up jitter is that the throttle valve is too dirty or the fuel injector has too much carbon.When the engine accumulates too much carbon, the gasoline sprayed by the fuel injector head during cold start will be absorbed by a large amount of carbon accumulation, resulting in excessive mixing gas during cold start and difficulty in starting.
3. This kind of jitter may be caused by indentation when the transmission gear and the transmission shaft mesh. This problem may exist in many powershift models, while AT and CVT models usually do not tremble when starting. Automatic manual transmission models such as DSG and DCT may tremble when changing gears.
1. The engine foot shakes. The automatic transmission car shakes badly when it is in the forward gear but has not started. It is likely that the engine foot has failed. In the process of using the car, the wear rate of the engine foot is much higher than that of other parts. After a long time or the engine foot Deformation and other problems may occur in certain quality defects.
2. This kind of jitter may be caused by indentation when the transmission gear meshes with the transmission shaft. This problem may exist in many powershift models, while AT and CVT models usually do not tremble when starting.Automatic manual transmission models such as DSG and DCT may tremble when changing gears.
3. Serious engine carbonization: Cars always have the problem of carbonization, including cylinder carbonization, throttle carbonisation, spark plug carbonation, intake carbonation, etc. When the engine accumulates too much carbon, it will affect the ignition energy, intake efficiency and air-fuel ratio of the car, resulting in unstable power output of the car, idling and acceleration jitter.
Solution: Check the oil pressure and replace the parts if necessary. Aging of engine parts. Car jitter is also related to the aging of engine feet (also known as claw pads).
When judging, set up the drive first.Bridge, plug the front wheel with safety plugs, start the engine and gradually change to high-speed gear, so that the drive wheel reaches the final test vibration speed. If the car body and the steering wheel shake at this time, it is the vibration caused by the transmission system.
It is relatively simple to solve this problem. You only need to replace the aging foot mat. It is recommended that the car owner choose the original accessories when replacing the foot mat.
APAC special tariff HS code listings
author: 2024-12-23 11:34Minimizing duties via HS code optimization
author: 2024-12-23 11:29Import restrictions by HS code category
author: 2024-12-23 10:33HS code mapping to product categories
author: 2024-12-23 09:21End-to-end supplier lifecycle management
author: 2024-12-23 11:13Trade data-driven market penetration
author: 2024-12-23 10:55How to leverage customs rulings data
author: 2024-12-23 10:34Food additives HS code classification
author: 2024-12-23 10:22How to reduce supply chain overheads
author: 2024-12-23 09:33947.53MB
Check199.85MB
Check755.87MB
Check173.99MB
Check641.78MB
Check732.98MB
Check874.14MB
Check644.95MB
Check551.34MB
Check247.96MB
Check136.95MB
Check364.64MB
Check636.14MB
Check753.99MB
Check523.79MB
Check599.31MB
Check856.27MB
Check849.76MB
Check986.44MB
Check148.57MB
Check142.55MB
Check361.56MB
Check925.32MB
Check688.83MB
Check347.89MB
Check728.31MB
Check735.59MB
Check866.33MB
Check138.68MB
Check514.71MB
Check786.12MB
Check237.59MB
Check277.51MB
Check189.85MB
Check879.62MB
Check267.93MB
CheckScan to install
Refined metals HS code references to discover more
Netizen comments More
680 Optimizing distribution using HS code data
2024-12-23 11:25 recommend
450 Global trade data storytelling
2024-12-23 11:19 recommend
2878 How to access niche export markets
2024-12-23 09:55 recommend
2853 HS code-based market readiness assessments
2024-12-23 09:51 recommend
1128 Container-level shipment data
2024-12-23 09:17 recommend