Real-time customs tariff analysis

List of the catalog of this article:

• 1, What to pay attention to in the whole car butter tutorial
• 2 、Car repair What is Real-time customs tariff analysisthe name of the butter used?
• 5
  、Can car butter heal itself when it is Real-time customs tariff analysisput into the hand
• 3, What are the parts of car buttering?
• 4、How to clean car butter

What to pay attention to in the whole car buttering tutorial

1. Where there is a butter mouth, you should beat butter once a week to ensure normal lubrication.

2. Truck separation bearing buttering: Find the clutch drum, and there is a lateral long strip of ventilation port on the cross-section of the clutch shaft. Insert it with a hose to estimate the fork, and inject butter with a syringe.

3. Cause unnecessary waste. The correct grease filling method should be to fill the bearing lumen and the hub cavity to fill 30%-50%.Maintenance of car cylinders. Car cylinders require extremely strict sealing. Some people like to apply a layer of butter to the cylinder pad when installing the cylinder, thinking that this can increase its tightness.

4. Method: Remove the oil seals on both sides, then clean the bearing with diesel and wipe the diesel on the bearing dry. First, apply one side of butter and put it on the oil seal, and then apply the other side of butter and install the oil seal. Its function is to reduce friction. The sealing effect can prevent external substances from invading the inside of the bearing.

Can car butter heal itself when it is put into the hand

1. No. The car's butter was hit into the index finger, and I had to go to the hospital for incision, drainage, irrigation and medicine change, which could not heal itself. Butter is made by separating the thin cream and skimmed milk in the milk, and the thin cream is stirred.

2. This is a natural process. There is no special effect method, and we can only let him get better. All we can do is to keep it clean and not get infected. The tissue, muscles and nerves in the incision generally take some time to recover. Generally, the recovery time is 3-6 months. Of.

3. Disease analysis: Butter cannot be absorbed when it enters the tissue, and it is easy to get infected. At present, it has been suppuration and should be treated in time to avoid complications such as osteomyelitis. Suggestions: It is recommended to have wound cleaning surgery, completely remove butter and necrotic tissue, disinfect, drain, drip antibiotics to fight infection, and change the medicine in time after the operation.

4. Because it has a certain degree of stickiness, it can be attached to the surface of the object and play a lubricating role. In some places, it must be buttered. Butter wipeThe hand can play the role of reducing friction, preventing rust, prolonging the service life, and maximizing the function of use.

5. Disease analysis: Hello, after butter is fingered, it will hinder the return of normal venous blood and tissue fluid due to the macromolecule particles such as oil in the subcutaneous soft tissue, resulting in congestion and edema of the soft tissue, causing swelling and pain.

What are the parts of car buttering?

Four-wheel suspension, transmission shaft, water pump and steering machine, main pin, two ends of the bow board, transmission shaft cross shaft, telescopic joint, hanger bearing bridge bearing adjustment arm, brake bar, if there is a semi-hanging, a layer should be applied to the drag plate, there is a butter mouth on the lever, and the pump is poured with a small amount of butter.

Basically, it is hit on the work-shaped board hanging ear, butter mouth, transmission shaft, direction pull rod, vertical shaft. Different loads, generally butter is in the great load friction part. Butter is used for lubrication. After the truck has been driving for a long time, the butter inside will be consumed. New supplements are needed to continue to maintain the car.

Which parts of the car need to be buttered? The hinges and lock cylinders on the door, as well as the sliding rails on the sunroof, generally need a little bit. The hinges on the door and the sliding rails on the sunroof can be coated with butter in the hinges on the door and each lock cylinder.

Butter is hit on: front and rear steel plate pins, transmission shaft cross shaft, suspension bridge, left and right balance shaft, turntable, steering machine telescopic fork.

Car repairWhat is the name of the butter used?

1. Usually, the kind of grease is used to butter the chassis in the parking lot.

2.: Calcium-based grease The biggest feature of calcium-based grease is yellow. This grease was used in early trucks, and the name butter comes from this.

3. Grease, commonly known as medium oil or butter,. Thick oily semi-solid. The friction part used in machinery plays the role of lubrication and sealing. It is also used on metal surfaces to fill voids and prevent rust. It is mainly composed of three parts: thickener, base oil and additives.

How to clean car butter

1. Butter is used to clean with salt-free butter with detergent, and it should be appliedIn the production of the industry, it specializes in cleaning the oil removal and cleaning liquid of metal 1653 materials. When applying, you should pay attention to the proportion of dilution liquid. Butter can be cleaned with gasoline or diesel engine in the car. It is best to clean up with gasoline in the car, because the volatile matter of gasoline in the car is better.

2. Butter is a sticky animal oil, which can be scrubbed with toluene or carbon tetrachloride solvent. The traces left can be removed by mixing alcohol and ammonia, or with alcohol soap. After applying Amway's multi-purpose detergent to the clothes for a few minutes, it can be washed off.

3. If you get butter for car repair, you can wipe the butter directly with a soft cloth dipped in gasoline, and then wash it with detergent and rinse it. Butter is processed from milk. After stirring the fresh milk, the thick object in the upper layer is the product of filtering out part of the water.

4. If there are traces, you can remove them by repeated wiping or expanding the range of brushing. You can also apply water to the stains on the clothes and spray them off with a high-pressure spray gun. Removal of pine oil stains When carrying pine wood, it is easy to make the clothes stick to pine oil, which should be removed in time.

5. This butter is not very easy to clean, but it can't be helped. It can be washed off with gasoline, or with paint thinner, but it smells a little thin. I hope it will be helpful to you.

6. Just use washing powder or detergent to wash. If it is dirty, you can add less sawdust to the washing powder or detergent to scrub, or you can also use a plastic brush.